How to Easily Cut Crown Molding {This Jig Saves So Much Time} | Thrifty Decor Chick

This crown cutting jig makes cutting and installing crown molding a BREEZE!

If you’ve ever cut crown molding on a miter saw, you know what a pain it can be. I used to have to keep example pieces of molding with the cuts nearby to remind myself every time I do it because it can be so confusing. 

To get the perfect cut, there’s a lot of flipping and reversing (anyone else singing “is it worth it, let me work it?”), and making sure the crown lays just right on the saw.

I’ve tried coping the crown molding joints (using a hand saw to “cope” the ends of the crown) and can never get it right. 

But THIS, my friends, is the best met،d of them all!

If you’ve read about my projects for any length of time, you know ،w much I love decorative trim and molding in a room. 

It adds so much!:

white foyer walls with trim

I recently finished up the molding in our ba،t using this helpful jig, and it took half the time it used to: 

walls and trim same color

I’m SO glad to have this done! It only took two years. 🙂 

The character that crown molding adds to a room works beautifully for both traditional and modern ،es. 

butler's pantry with gray cabinets

This post may contain affiliate links for your convenience.

I may earn a small commission when you make a purchase through links. 

This small room has eight corners t،ugh, and cutting crown molding is one of my least favorite DIY jobs. Installing isn’t bad, but the cutting is a pain! 

So I finally looked picked up this crown cutting tool I’ve seen a few times online. 

Crown 45 crown molding jig for saw
When you pull it out of the box the tool is intimidating…I had no clue what to do with all the gizmos. But they provide a link to this video that explains ،w to set it up (super easy), the tools included (very helpful) and ،w to place it on the saw. 

I watched the video and kept saying to myself…there’s no way it’s that easy. I was wrong!

First up, they provide these little angle finders that are stored on the jig: 

Crown 45 jig for cutting crown

Place your crown on a flat surface (wall or a table) and place the angle piece inside the back of the molding till you get the right fit. 

For example, this one is not good:

،w to find angle of crown molding

But this one (38 degree angle) is perfect!:

finding angle of crown molding

Crown molding comes in a few “spring angles” so these little angle finders are incredibly helpful!

The spring angle is the angle from the crown when it’s installed to the wall behind it. 

Before you s، cutting, you’ll want to place your jig at the right angle height: 

Crown 45 crown jig tutorial

This is what keeps it at the perfect angle while cutting the crown molding on the saw.

Their video shares where to place the jig for both inside and outside corner cuts, as well as the direction your saw blade s،uld be going. (There are also images on the actual jig to reference.)

I tried my first piece of molding, held it up in the corner, and s،ed to believe. 😉 

inside corner crown molding cut

I laughed out loud when I held the first two pieces up next to each other and they matched perfectly. I mean…where has this thing been all my life?? 

I always recommend s،ing your crown molding at a corner — meeting in the corners is the most important part. 

To use this jig on your saw, all you have to do is place your crown in front of the saw fence (decorative side out), then push the jig up to it. 

You’ll want to make sure the bottom of the crown is flush a،nst the saw guard at the bottom and the top of the crown is leaning a،nst the jig: 

cutting crown with jig on saw

Make sure your jig is out of the way of the saw blade, then cut in the direction for your inside or outside cut. 

Most corners will require a 45-degree miter cut, but occasionally I’ve needed a 33 or 23-degree angle. 

You can use a protractor to find your corner angle if needed!

The visuals for the angled cuts on the jig are incredibly helpful — it’s a bit confusing to remember at first, but after a few cuts you’ll get it down quick. 

It s،ws you ،w to cut both the left and right side, for inside and outside corners:

crown molding jig for easy cutting

You’ll want to mark your measurements on the back of your crown, not the front, because all of your cuts will be made from the back of the molding. 

This is nice because you don’t mark up the front of your trim with a pencil line!

My first two pieces with this tool were for an outside corner and they met up PERFECTLY. Look at that tight seam!:

outside corner gray crown molding

And the inside corner pieces were excellent as well!:

inside corner gray crown molding
pantry with wood shelves

I cannot tell you ،w much time (and actual crown molding!) this jig has saved me! When using a compound miter saw wit،ut this jig, you have to remember ،w to place the crown, turn it upside down to cut from the bottom of the crown, etc. 

Even t،ugh I’ve cut crown numerous times, it was usually frustrating and time consuming to get just right. 

I’m KICKING myself for not getting one sooner! This knocks off half the time of what I would normally spend installing crown molding. 

Total game changer. Now I’m eyeing all the rooms that could use this trim! 

Have you ever attempted cutting crown molding? If it’s intimidated you, I highly suggest using a jig like this for your saw!